The version of CRIU which is included with CentOS is updated with every minor CentOS release (at least at the time of writing this) since 7.2, but once the minor CentOS release is available CRIU is not updated anymore until the next minor release. To make it easier to use the latest version of CRIU on CentOS I am now also rebuilding the latest version in COPR for CentOS: https://copr.fedorainfracloud.org/coprs/adrian/criu-el7/.

To enable my CRIU COPR on CentOS following steps are necessary:

• yum install yum-plugin-copr
• yum copr enable adrian/criu-el7

And then the latest version of CRIU can be installed using yum install criu.

After having worked on optimizing live container migration based on runc (pre-copy migration and post-copy migration) I tried to optimize container migration in LXD.

After a few initial discussions with Christian I started with pre-copy migration. Container migration in LXD is based on CRIU, just as in runc and CRIU's pre-copy migration support is based on dirty page tracking support of Linux: SOFT-DIRTY PTEs.

As LXD uses LXC for the actual container checkpointing and restoring I was curious if there was already pre-copy migration support in LXC. After figuring out the right command-line parameters it almost worked thanks to the great checkpoint and restore support implemented by Tycho some time ago.

Now that I knew that it works in LXC I focused on getting pre-copy migration support into LXD. LXD supports container live migration using the move command: lxc move <container> <remote>:<container>
This move command, however, did not use any optimization yet. It basically did:

1. Initial sync of the filesystem
2. Checkpoint container using CRIU
3. Transfer container checkpoint
4. Final sync of the filesystem
5. Restart container on the remote system

The downtime for the container in this scenario is between step 2 and step
5 and depends on the used memory of the processes inside the container. The goal of pre-copy migration is to dump the memory of the container and transfer it to the remote destination while the container keeps on running and doing a final dump with only the memory pages that changed since the last pre-dump (more about process migration optimization theories).

Back to LXD: At the end of the day I had a very rough (and very hardcoded) first pre-copy migration implementation ready and I kept working on it until it was ready to be submitted upstream. The pull request has already been merged upstream and now LXD supports pre-copy migration.

As not all architecture/kernel/criu combinations support pre-copy migration it has to be turned on manually right now, but we already discussed adding pre-copy support detection to LXC. To tell LXD to use pre-copy migration, the parameter 'migration.incremental.memory' needs to be set to 'true'. Once that is done and if LXD is instructed to migrate a container the following will happen:

• Initial sync of the filesystem
• Start pre-copy checkpointing loop using CRIU
  • Check if maximum number pre-copy iterations has been reached
  • Check if threshold of unchanged memory pages has been reached
  • Transfer container checkpoint
  • Continue pre-copy checkpointing loop if neither of those conditions is true
• Final container delta checkpoint using CRIU
• Transfer final delta checkpoint
• Final sync of the filesystem
• Restart container on the remote system

So instead of doing a single checkpoint and transferring it, there are now multiple pre-copy checkpoints and the container keeps on running during those transfers. The container is only suspended during the last delta checkpoint and the transfer of the last delta checkpoint. In many cases this reduces the container downtime during migration, but there is the possibility that pre-copy migration also increases the container downtime during migration. This depends (as always) on the workload.

To control how many pre-copy iterations LXD does there are two additional variables:

1. migration.incremental.memory.iterations (defaults to 10)
2. migration.incremental.memory.goal (defaults to 70%)

The first variable (iterations) is used to tell LXD how many pre-copy iterations it should do before doing the final dump and the second variable (goal) is used to tell LXD the percentage of pre-copied memory pages that should not change between pre-copy iterations before doing the final dump.

So LXD, in the default configuration, does either 10 pre-copy iterations before doing the final migration or the final migration is triggered when at least 70% of the memory pages have been transferred by the last pre-copy iteration.

Now that this pull request is merged and if pre-copy migration is enabled a lxc move <container> <remote>:<container> should live migrate the container with a reduced downtime.

I want to thank Christian for the collaboration on getting CRIU's pre-copy support into LXD, Tycho for his work preparing LXC and LXD to support migration so nicely and the developers of p.haul for the ideas how to implement pre-copy container migration. Next step: lazy migration.